A custom insole can match the shape of a foot beautifully. The harder question is what it does to the pressure under that foot when the person actually walks. What if we could build the answer into the material itself, making it more compliant exactly where the foot needs relief?
Brittney Muir, Bill Ledoux, Scott Telfer, and their colleagues at VA Puget Sound and the University of Washington put that idea to the test in PLOS One. The pressure maps are worth a close look.

Same feet, four conditions
Twenty-five veterans with diabetes and elevated plantar pressure walked in the lab with no therapeutic insole, a conventional custom insole, and two 3D-printed designs. One printed design used measured pressure to position a softer lattice around the hotspot. The other used finite-element modeling, a computer simulation of how the foot and insole bear load, to guide the design. Each participant tested all four conditions.
Lower pressure at the hotspot
The conventional custom insole already reduced loading compared with no insole. Both printed designs went further at the target. Peak pressure captures the highest load; the pressure–time integral captures pressure accumulated over the time the foot is loaded during a step.
| At the target | Pressure-based design | Finite-element design |
|---|---|---|
| Peak plantar pressure | 22% lower | 24% lower |
| Pressure–time integral | 19% lower | 35% lower |
What happened next door matters, too. The finite-element design lowered the pressure–time integral in neighboring regions compared with the conventional insole, although adjacent peak pressure was not significantly lower in that comparison. Some neighboring measurements still exceeded 200 kPa. A gentler hotspot is a win only if we’re also paying attention to where the load goes.
A better map still has to make it out the door
The finite-element design delivered the largest reported reduction in pressure–time integral at the target, but it was the least preferred of the three insoles: six participants chose it, compared with ten for the pressure-based design and nine for the conventional one. Fit and comfort are part of the intervention. An insole can only offload the steps people actually take in it.
Sicco Bus and colleagues showed why we need both a pressure result and a wear result. In their randomized custom-footwear trial, better offloading did not significantly reduce recurrence overall. The group that wore the prescribed footwear for at least 80% of steps had fewer recurrences with improved offloading, an encouraging subgroup finding. More recently, Lisa Vossen, Jaap van Netten, Bus and colleagues tested a practical response in DIASSIST: combine optimized footwear, an indoor option, education and feedback. That package improved objectively measured footwear adherence. As we discussed in our DIASSIST post, what people can comfortably wear at home deserves as much attention as what we fit in clinic.
There’s another way to bring the pressure map out of the lab. Breanne Everett and the Orpyx team have worked on sensing pressure in everyday life. In a separate randomized proof-of-concept study co-funded by Diabetes UK and Orpyx, Caroline Abbott, Katie Chatwin and colleagues reported fewer recurrent ulcer sites when a sensing insole gave people real-time feedback. That’s a different intervention from Muir’s printed insoles, but it raises an interesting design question: can we combine an insole shaped to protect the foot with feedback that helps the person protect it between visits? We’re working with Orpyx in WIRED-UP; my Orpyx relationships are disclosed in our Nature Primer.
This is a useful follow-up to our recent discussion of standing versus walking pressure. Measure the foot in motion, design for the place that needs relief, then check what happened in the shoe at that spot and the spots around it. This study shows what is possible on a lab walkway. It didn’t measure long-term wear or whether these insoles prevent ulcers. That’s the next question I’d like to see answered.
The next wound-care startup might start with the insole
Here’s the startup I’d like to see: mass customization for tissue repair. Measure pressure while someone walks, manufacture an insole tuned to that person’s foot, and then verify the result in the shoe. Build in the fitting, the recheck and the adjustments. The product is a repeatable way to get a truly custom fit and verify that it takes pressure off the right spot.
There’s a thread running through our recent posts on why standing pressure can mislead and on how WIRED-UP is studying ulcer-free days after healing. And as Edgar Peters, Larry Lavery and colleagues remind us in their study of repeat X-rays, what we measure and when we measure it can change the answer. Here, the measure is in-shoe pressure during walking. The outcome we ultimately want is more time with intact skin.
What if we paid for ulcer-free days?
Imagine that after a costly reconstruction, or after a course of a cellular, acellular or matrix-like product (CAMP), we already had the cost of pressure-verified insoles, fitting and follow-up built into the episode of care. Why pay to close the wound and then leave protecting that repair to a separate transaction?
Better yet, imagine that part of the payment depended on performance: how many days the patient was alive and ulcer-free over a fixed period from the start of treatment. Days with the original ulcer still open would not count, so faster healing earns more ulcer-free days. A recurrence takes days away again, so keeping the wound closed matters too. I’d still report time to healing and recurrence separately, and adjust for baseline risk so teams aren’t penalized for taking on the hardest cases.
That’s a model to test, not a claim that these insoles already save money or prevent ulcers. Start by showing that people can get the insoles, wear them, and keep the pressure reduction over time. Then ask whether the whole pathway buys what patients actually want: more ulcer-free, activity-rich days.
Read the study
Muir BC, Nickerson KA, Carranza C, Varre MS, Nagle-Christensen A, Heino D, Li EY, Ledoux WR, Telfer S. Improving offloading in diabetic feet: 3D-printed custom accommodative insoles outperform standard of care. PLOS One. 2026;21(11):e0363325. doi:10.1371/journal.pone.0363325.
#ActAgainstAmputation #DiabeticFoot #Offloading #LimbPreservation
Leave a Reply